空飛ぶロボットのつくりかた

ロボットをつくるために必要な技術をまとめます。ロボットの未来についても考えたりします。

NeoPixel Ringで遊んでみる

やりたいこと

Neo Pixcel の LEDをいい感じに光らせたい💡

f:id:robonchu:20180325215325j:plain

購入したNeo Pixcel LED

780円〜♪

https://www.amazon.co.jp/waves-NeoPixel-%E3%83%8D%E3%82%AA%E3%83%94%E3%82%AF%E3%82%BB%E3%83%AB-WS2812B-24%E5%80%8B/dp/B07926DQWQ

教科書

https://learn.adafruit.com/florabrella/test-the-neopixel-strip

ハンダ付け

👇こんな感じ

f:id:robonchu:20180325214712j:plain

配線

  • VCC -> 5V

  • GND -> GND

  • IN -> 6番pin

下記写真参考

Arduinoの設定

robonchu.hatenablog.com

NeoPixelのライブラリ設定

  1. GitHub - adafruit/Adafruit_NeoPixel: Neo Pixels!からクローン

  2. クローンしてきたディレクトリを~/arduino-1.8.5/libraries/NeoPixelに配置

スケッチ

#include <Adafruit_NeoPixel.h>

#define PIN 6

// Parameter 1 = number of pixels in strip
// Parameter 2 = pin number (most are valid)
// Parameter 3 = pixel type flags, add together as needed:
//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
Adafruit_NeoPixel strip = Adafruit_NeoPixel(160, PIN, NEO_GRB + NEO_KHZ800);

void setup() {
  strip.begin();
  strip.setBrightness(30); //adjust brightness here
  strip.show(); // Initialize all pixels to 'off'
}

void loop() {
  // Some example procedures showing how to display to the pixels:
  colorWipe(strip.Color(255, 0, 0), 50); // Red
  colorWipe(strip.Color(0, 255, 0), 50); // Green
  colorWipe(strip.Color(0, 0, 255), 50); // Blue
  rainbow(20);
  rainbowCycle(20);
}

// Fill the dots one after the other with a color
void colorWipe(uint32_t c, uint8_t wait) {
  for(uint16_t i=0; i<strip.numPixels(); i++) {
      strip.setPixelColor(i, c);
      strip.show();
      delay(wait);
  }
}

void rainbow(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256; j++) {
    for(i=0; i<strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel((i+j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

// Slightly different, this makes the rainbow equally distributed throughout
void rainbowCycle(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256*5; j++) { // 5 cycles of all colors on wheel
    for(i=0; i< strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel(((i * 256 / strip.numPixels()) + j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

// Input a value 0 to 255 to get a color value.
// The colours are a transition r - g - b - back to r.
uint32_t Wheel(byte WheelPos) {
  if(WheelPos < 85) {
   return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
  } else if(WheelPos < 170) {
   WheelPos -= 85;
   return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
  } else {
   WheelPos -= 170;
   return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
  }
}

これを書き込めばOK💡

f:id:robonchu:20180325215217j:plain

RasPiでトライ

参考:

所感

とても綺麗✨

色んな光らせ方を考えていきたいな〜

参考